History of Hard DIsk: July 2011

Tuesday, 26 July 2011

Hard disk drive

From Wikipedia, the free encyclopedia

"Hard drive" redirects here. For other uses, see Hard drive (disambiguation).

Hard disk drive
Interior of a hard disk drive
Date invented	24 December 1954^[1]
Invented by	An IBM team led by Rey Johnson

Video of an opened hard drive

A hard disk drive (HDD; also hard drive or hard disk)^[2] is a non-volatile, random access digital data storage device. It features rotating rigid platters on a motor-driven spindle within a protective enclosure. Data is magnetically read from and written to the platter by read/write heads that float on a film of air above the platters.
Introduced by IBM in 1956, hard disk drives have decreased in cost and physical size over the years while dramatically increasing in capacity. Hard disk drives have been the dominant device for secondary storage of data in general purpose computers since the early 1960s.^[3] They have maintained this position because advances in their recording density have kept pace with the requirements for secondary storage.^[3] Today's HDDs operate on high-speed serial interfaces; i.e., serial ATA (SATA) or serial attached SCSI (SAS).

[hide]

1 History
2 Technology
- 2.1 Magnetic recording
- 2.2 Components
- 2.3 Error handling
- 2.4 Future development
3 Capacity
- 3.1 Units of measuring capacity
- 3.2 HDD formatting
- 3.3 Redundancy
- 3.4 HDD parameters to calculate capacity
4 Form factors
- 4.1 Current hard disk form factors
- 4.2 Obsolete hard disk form factors
5 Performance characteristics
- 5.1 Access time
  - 5.1.1 Interleave
  - 5.1.2 Seek time
  - 5.1.3 Rotational latency
  - 5.1.4 Data transfer rate
- 5.2 Power consumption
  - 5.2.1 Power management
- 5.3 Audible noise
- 5.4 Shock resistance
6 Access and interfaces
- 6.1 Disk interface families used in personal computers
7 Integrity
- 7.1 Actuation of moving arm
- 7.2 Landing zones and load/unload technology
  - 7.2.1 Landing zones
  - 7.2.2 Unloading
- 7.3 Failures and metrics
8 External removable drives
9 Market segments
10 Sales
11 Icons
12 Manufacturers
13 See also
14 Notes and references
15 Further reading
16 External links

History

Main article: History of hard disk drives

Hard disk drives were introduced in 1956 as data storage for an IBM real time transaction processing computer^[4] and were developed for use with general purpose mainframe and mini computers.
As the 1980s began, hard disk drives were a rare and very expensive additional feature on personal computers (PCs); however by the late '80s, hard disk drives were standard on all but the cheapest PC.
Most hard disk drives in the early 1980s were sold to PC end users as an add on subsystem, not under the drive manufacturer's name but by Systems Integrators such as the Corvus Disk System or the systems manufacturer such as the Apple ProFile. The IBM PC/XT in 1983 included an internal standard 10MB hard disk drive, and soon thereafter internal hard disk drives proliferated on personal computers.
External hard disk drives remained popular for much longer on the Apple Macintosh. Every Mac made between 1986 and 1998 has a SCSI port on the back, making external expansion easy; also, "toaster" Compact Macs did not have easily accessible hard drive bays (or, in the case of the Mac Plus, any hard drive bay at all), so on those models, external SCSI disks were the only reasonable option.
Driven by areal density doubling every two to four years since their invention, HDDs have changed in many ways, a few highlights include:

Capacity per HDD increasing from 3.75 megabytes to greater than 1 terabyte, a greater than 270-thousand-to-1 improvement.
Size of HDD decreasing from 87.9 cubic feet (a double wide refrigerator) to 0.002 cubic feet (2½-inch form factor, a pack of cards), a greater than 44-thousand-to-1 improvement.
Price decreasing from about $15,000 per megabyte to less than $0.0001 per megabyte ($100/1 terabyte), a greater than 150-million-to-1 improvement.^[5]
Average access time decreasing from greater than 0.1 second to a few thousandths of a second, a greater than 40-to-1 improvement.
Market application expanding from general purpose computers to most computing applications including consumer applications

Technology

[edit] Magnetic recording

Form factors

5¼″ full height 110 MB HDD,
2½″ (8.5 mm) 6495 MB HDD,
US/UK pennies for comparison.

A 2.5 inch SATA hard drive from a Sony Vaio E series laptop.

Six hard drives with 8″, 5.25″, 3.5″, 2.5″, 1.8″, and 1″ disks, partially disassembled to show platters and read-write heads, with a ruler showing inches.

Mainframe and minicomputer hard disks were of widely varying dimensions, typically in free standing cabinets the size of washing machines (e.g. HP 7935 and DEC RP06 Disk Drives) or designed so that dimensions enabled placement in a 19" rack (e.g. Diablo Model 31). In 1962, IBM introduced its model 1311 disk, which used 14 inch (nominal size) platters. This became a standard size for mainframe and minicomputer drives for many years,^[45] but such large platters were never used with microprocessor-based systems.
With increasing sales of microcomputers having built in floppy-disk drives (FDDs), HDDs that would fit to the FDD mountings became desirable, and this led to the evolution of the market towards drives with certain Form factors, initially derived from the sizes of 8-inch, 5.25-inch, and 3.5-inch floppy disk drives. Smaller sizes than 3.5 inches have emerged as popular in the marketplace and/or been decided by various industry groups.

8 inch: 9.5 in × 4.624 in × 14.25 in (241.3 mm × 117.5 mm × 362 mm)
In 1979, Shugart Associates' SA1000 was the first form factor compatible HDD, having the same dimensions and a compatible interface to the 8″ FDD.
5.25 inch: 5.75 in × 3.25 in × 8 in (146.1 mm × 82.55 mm × 203 mm)
This smaller form factor, first used in an HDD by Seagate in 1980,^[46] was the same size as full-height 5¹⁄₄-inch-diameter (130 mm) FDD, 3.25-inches high. This is twice as high as "half height"; i.e., 1.63 in (41.4 mm). Most desktop models of drives for optical 120 mm disks (DVD, CD) use the half height 5¼″ dimension, but it fell out of fashion for HDDs. The Quantum Bigfoot HDD was the last to use it in the late 1990s, with "low-profile" (≈25 mm) and "ultra-low-profile" (≈20 mm) high versions.
3.5 inch: 4 in × 1 in × 5.75 in (101.6 mm × 25.4 mm × 146 mm) = 376.77344 cm³
This smaller form factor, first used in an HDD by Rodime in 1983,^[47] was the same size as the "half height" 3½″ FDD, i.e., 1.63 inches high. Today it has been largely superseded by 1-inch high "slimline" or "low-profile" versions of this form factor which is used by most desktop HDDs.
2.5 inch: 2.75 in × 0.275–0.59 in × 3.945 in (69.85 mm × 7–15 mm × 100 mm) = 48.895–104.775 cm³
This smaller form factor was introduced by PrairieTek in 1988;^[48] there is no corresponding FDD. It is widely used today for solid-state drives and for hard-disk drives in mobile devices (laptops, music players, etc.) and as of 2008 replacing 3.5 inch enterprise-class drives.^[49] It is also used in the Playstation 3^[50] and Xbox 360^{[citation needed]} video game consoles. Today, the dominant height of this form factor is 9.5 mm for laptop drives (usually having two platters inside), but higher capacity drives have a height of 12.5 mm (usually having three platters). Enterprise-class drives can have a height up to 15 mm.^[51] Seagate has released a wafer-thin 7mm drive aimed at entry level laptops and high end netbooks in December 2009.^[52]
1.8 inch: 54 mm × 8 mm × 71 mm = 30.672 cm³
This form factor, originally introduced by Integral Peripherals in 1993, has evolved into the ATA-7 LIF with dimensions as stated. It was increasingly used in digital audio players and subnotebooks, but is rarely used today. An original variant exists for 2–5GB sized HDDs that fit directly into a PC card expansion slot. These became popular for their use in iPods and other HDD based MP3 players.
1 inch: 42.8 mm × 5 mm × 36.4 mm
This form factor was introduced in 1999 as IBM's Microdrive to fit inside a CF Type II slot. Samsung calls the same form factor "1.3 inch" drive in its product literature.^[53]
0.85 inch: 24 mm × 5 mm × 32 mm

Interleave

A low-level formatting tool running tests to find the highest performance interleave choice for a 10-megabyte IBM PC XT hard drive.

Sector interleave is a mostly obsolete device characteristic related to access time, dating back to when computers were too slow to be able to read large continuous streams of data. Interleaving introduced gaps between data sectors to allow time for slow equipment to get ready to read the next block of data. Without interleaving, the next logical sector would arrive at the read/write head before the equipment was ready, requiring the system to wait for another complete disk revolution before reading could be performed.
However, because interleaving introduces intentional physical delays into the drive mechanism, setting the interleave to a ratio higher than required causes unnecessary delays for equipment that has the performance needed to read sectors more quickly. The interleaving ratio was therefore usually chosen by the end-user to suit their particular computer system's performance capabilities when the drive was first installed in their system.
Modern technology is capable of reading data as fast as it can be obtained from the spinning platters, so hard drives usually have a fixed sector interleave ratio of 1:1, which is effectively no interleaving being used.

[edit] Seek time

Average seek time ranges from 3 ms^[72] for high-end server drives, to 15 ms for mobile drives, with the most common mobile drives at about 12 ms^[73] and the most common desktop type typically being around 9 ms. The first HDD had an average seek time of about 600 ms and by the middle 1970s HDDs were available with seek times of about 25 ms. Some early PC drives used a stepper motor to move the heads, and as a result had seek times as slow as 80–120 ms, but this was quickly improved by voice coil type actuation in the 1980s, reducing seek times to around 20 ms. Seek time has continued to improve slowly over time.
Some desktop and laptop computer systems allow the user to make a tradeoff between seek performance and drive noise. Faster seek rates typically require more energy usage to quickly move the heads across the platter, causing loud noises from the pivot bearing and greater device vibrations as the heads are rapidly accelerated during the start of the seek motion and decelerated at the end of the seek motion. Quiet operation reduces movement speed and acceleration rates, but at a cost of reduced seek performance.

Disk interface families used in personal computers

Notable families of disk interfaces include:

Several Parallel ATA hard disk drives

Historical bit serial interfaces connect a hard disk drive (HDD) to a hard disk controller (HDC) with two cables, one for control and one for data. (Each drive also has an additional cable for power, usually connecting it directly to the power supply unit). The HDC provided significant functions such as serial/parallel conversion, data separation, and track formatting, and required matching to the drive (after formatting) in order to assure reliability. Each control cable could serve two or more drives, while a dedicated (and smaller) data cable served each drive.
- ST506 used MFM (Modified Frequency Modulation) for the data encoding method.
- ST412 was available in either MFM or RLL (Run Length Limited) encoding variants.
- Enhanced Small Disk Interface (ESDI) was an industry standard interface similar to ST412 supporting higher data rates between the processor and the disk drive.

Modern bit serial interfaces connect a hard disk drive to a host bus interface adapter (today typically integrated into the "south bridge") with one data/control cable. (As for historical bit serial interfaces above, each drive also has an additional power cable, usually direct to the power supply unit.)
- Fibre Channel (FC), is a successor to parallel SCSI interface on enterprise market. It is a serial protocol. In disk drives usually the Fibre Channel Arbitrated Loop (FC-AL) connection topology is used. FC has much broader usage than mere disk interfaces, and it is the cornerstone of storage area networks (SANs). Recently other protocols for this field, like iSCSI and ATA over Ethernet have been developed as well. Confusingly, drives usually use copper twisted-pair cables for Fibre Channel, not fibre optics. The latter are traditionally reserved for larger devices, such as servers or disk array controllers.
- Serial ATA (SATA). The SATA data cable has one data pair for differential transmission of data to the device, and one pair for differential receiving from the device, just like EIA-422. That requires that data be transmitted serially. Similar differential signaling system is used in RS485, LocalTalk, USB, Firewire, and differential SCSI.
- Serial Attached SCSI (SAS). The SAS is a new generation serial communication protocol for devices designed to allow for much higher speed data transfers and is compatible with SATA. SAS uses a mechanically identical data and power connector to standard 3.5-inch SATA1/SATA2 HDDs, and many server-oriented SAS RAID controllers are also capable of addressing SATA hard drives. SAS uses serial communication instead of the parallel method found in traditional SCSI devices but still uses SCSI commands.

Inner view of a 1998 Seagate hard disk drive which used Parallel ATA interface

Word serial interfaces connect a hard disk drive to a host bus adapter (today typically integrated into the "south bridge") with one cable for combined data/control. (As for all bit serial interfaces above, each drive also has an additional power cable, usually direct to the power supply unit.) The earliest versions of these interfaces typically had a 8 bit parallel data transfer to/from the drive, but 16-bit versions became much more common, and there are 32 bit versions. Modern variants have serial data transfer. The word nature of data transfer makes the design of a host bus adapter significantly simpler than that of the precursor HDD controller.

Integrity

An IBM HDD head resting on a disk platter. Since the drive is not in operation, the head is simply pressed against the disk by the suspension.

Close-up of a hard disk head resting on a disk platter. A reflection of the head and its suspension is visible on the mirror-like disk.

Due to the extremely close spacing between the heads and the disk surface, hard disk drives are vulnerable to being damaged by a head crash—a failure of the disk in which the head scrapes across the platter surface, often grinding away the thin magnetic film and causing data loss. Head crashes can be caused by electronic failure, a sudden power failure, physical shock, contamination of the drive's internal enclosure, wear and tear, corrosion, or poorly manufactured platters and heads.
The HDD's spindle system relies on air pressure inside the disk enclosure to support the heads at their proper flying height while the disk rotates. Hard disk drives require a certain range of air pressures in order to operate properly. The connection to the external environment and pressure occurs through a small hole in the enclosure (about 0.5 mm in breadth), usually with a filter on the inside (the breather filter).^[83] If the air pressure is too low, then there is not enough lift for the flying head, so the head gets too close to the disk, and there is a risk of head crashes and data loss. Specially manufactured sealed and pressurized disks are needed for reliable high-altitude operation, above about 3,000 m (10,000 feet).^[84] Modern disks include temperature sensors and adjust their operation to the operating environment. Breather holes can be seen on all disk drives—they usually have a sticker next to them, warning the user not to cover the holes. The air inside the operating drive is constantly moving too, being swept in motion by friction with the spinning platters. This air passes through an internal recirculation (or "recirc") filter to remove any leftover contaminants from manufacture, any particles or chemicals that may have somehow entered the enclosure, and any particles or outgassing generated internally in normal operation. Very high humidity for extended periods can corrode the heads and platters.

For giant magnetoresistive (GMR) heads in particular, a minor head crash from contamination (that does not remove the magnetic surface of the disk) still results in the head temporarily overheating, due to friction with the disk surface, and can render the data unreadable for a short period until the head temperature stabilizes (so called "thermal asperity", a problem which can partially be dealt with by proper electronic filtering of the read signal).

Landing zones and load/unload technology

A read/write head from a circa-1998 Fujitsu 3.5-inch hard disk. The area pictured is approximately 2.0 mm x 3.0mm.

Microphotograph of an older generation hard disk head and slider (1990s). The size of the front face (which is the "trailing face" of the slider) is about 0.3 mm × 1.0 mm. It is the location of the actual head (magnetic sensors). The non-visible bottom face of the slider is about 1.0 mm × 1.25 mm (so-called "nano" size) and faces the platter. It contains the lithographically micro-machined air bearing surface (ABS) that allows the slider to fly in a highly controlled fashion. One functional part of the head is the round, orange structure visible in the middle—the lithographically defined copper coil of the write transducer. Also note the electric connections by wires bonded to gold-plated pads.

During normal operation heads in HDDs fly above the data recorded on the disks. Modern HDDs prevent power interruptions or other malfunctions from landing its heads in the data zone by either physically moving (parking) the heads to a special landing zone on the platters that is not used for data storage, or by physically locking the heads in a suspended (unloaded) position raised off the platters. Some early PC HDDs did not park the heads automatically when power was prematurely disconnected and the heads would land on data. In some other early units the user manually parked the heads by running a program to park the HDD's heads.

[edit] Landing zones

A landing zone is an area of the platter usually near its inner diameter (ID), where no data are stored. This area is called the Contact Start/Stop (CSS) zone. Disks are designed such that either a spring or, more recently, rotational inertia in the platters is used to park the heads in the case of unexpected power loss. In this case, the spindle motor temporarily acts as a generator, providing power to the actuator.

Spring tension from the head mounting constantly pushes the heads towards the platter. While the disk is spinning, the heads are supported by an air bearing and experience no physical contact or wear. In CSS drives the sliders carrying the head sensors (often also just called heads) are designed to survive a number of landings and takeoffs from the media surface, though wear and tear on these microscopic components eventually takes its toll. Most manufacturers design the sliders to survive 50,000 contact cycles before the chance of damage on startup rises above 50%. However, the decay rate is not linear: when a disk is younger and has had fewer start-stop cycles, it has a better chance of surviving the next startup than an older, higher-mileage disk (as the head literally drags along the disk's surface until the air bearing is established). For example, the Seagate Barracuda 7200.10 series of desktop hard disks are rated to 50,000 start-stop cycles, in other words no failures attributed to the head-platter interface were seen before at least 50,000 start-stop cycles during testing.^[85]

Monday, 25 July 2011

Icons

Hard drives are traditionally symbolized as either a stylized stack of platters (in orthographic projection) or, more abstractly, as a cylinder. This is particularly found in schematic diagrams or on indicator lights, as on laptops, to indicate hard drive access. In most modern operating systems, hard drives are instead represented by an illustration or photograph of a hard drive enclosure. These are illustrated below.

Today, hard drives are symbolized by a picture of the enclosure.
Schematically, hard drives may be represented by cylinders or stacks of platters, as in this RAID diagram.
The cylinder schematic derives from hard drives internally being a stack of platters, as in these 1970s vintage disk pack (cover removed).